|
|
| We are please to offer for your consideration a very exclusive line of Ural Accessories. Designed and manufactured in Oregon USA by Raceway Services (... quality without compromise)
 | Power Arc Ignition System Optically-triggered Ural-specific Power Arc Ignition Systems. Retrofit Type 3 thru 5 Russian ignitions on old Urals or improve your Ducati ignition on newer Urals. Two ignition curves are loaded into the processor - one is the standard Ural/Ducati curve, the second curve can be accessed via a momentary on, toggle or VOES switch. Optical reader triggered ignition means no spark scatter on acceleration /deceleration (in other words you get very precise timing).
- $385.00 kit |
 | Power Arc Coil Mount Heavy duty coil mount for Power Arc ignition coils. Fits all Ural motorcycles. Simply remove steering damper anchor bolt, slide coil mount under damper anchor, replace bolt, bolt coil on and it’s a done deal.
- $24.95 each |
 | Ural 750 32mm Flat Slide High Performance Carburetors 32 mm flat-slide high-performance carburetors for the Ural 750. Born and bred from the PWK with an unusual twist - an American-designed circuit plate. Reversible side idle speed screws. Straight up pull enrichners. Change jets without removing fuel bowl. Rubber manifold boots match Ural manifold stud pattern.
- $185.00 each
|
 | Dnepr 650, Chang Jiang, Early BMW Boxer 30mm Flat Slide High Performance Carburetors 30mm, flat slide, high-performance carburetors for: Ural 650, Dnepr 650, Chang Jiang, early BMW boxers. Feature straight-up pull-type enrichners, reversible side idle speed adjuster screws, CNC machined aluminum adapter manifolds with “O” ring seals.
- $189.00 each |
 | Phenolic Carburetor Heat Block A lot of cylinder head heat transfers through the flanged rubber manifold into the carburetor, and the rubber flanges themselves may warp as a result, causing the fuel/air mixture to go lean, which causes more heat - it's a vicious cycle. These water-jet, burr-free 1/4" thick phenolic heat blocks provide an effective barrier. Simply install between the cylinder head and rubber manifold. Many shown in photo, two required per motorcycle.
- $6.50 each |
 | Fuel Line Quick-Disconnects for Fuel Tank Cross-Over Line A fuel spill is inevitable when removing the Ural fuel cross-over line. These proven inline nylon/stainless steel quick-disconnects will make that problem go away once installed. Simply press the tab and the male and female disconnects separate. The tab lock stays "cocked", simply push them together and the spring-loaded tab locks them together again. Supplied with 1 foot of EPO-NBR gasahol and MTBE additive resistant fuel line, in addition to four Helix-type hose clamps.
- $39.95 kit |
 | Dunstall Mufflers A classic design first created by Paul Dunstall that still looks great today. Slow taper/short reverse cone design. Removable and re-packable silencer. Sold for "off road or competition use only". Great sound. Header reduction bushing and bracket included. Mufflers have a chrome finish.
- $85.00 each (two required for motorcycle)
|
 | Black High-Mount Exhaust System Black ceramic-coated high-mount exhaust system. Intended for "off-pavement" riders, but applicable to any model Ural. Free-flowing with matched-length headers for each side. Mounting brackets and hardware included. Photos show one exhaust system, two complete systems are included in set.
- $595.00 set |
 | Reverse Shift Kit Our most popular hand shift kit since 1999! Allows shifting into reverse via hand lever alongside gas tank. Works great as a neutral finder too! Gloss powder coat finish. Stainless steel hardware. Makes getting into reverse a breeze!
- $245.00 kit |
 | 2WD/Reverse Shift Kit Our 2-wheel drive and reverse shift kit eliminates having to bend over and reach behind your ankles to engage 2WD or reverse on your Gear-Up or Patrol.
- $335.00 kit |
 | "Twin Stick" Forward/Reverse Shift Kit Our much improved original two lever shift kit system for all Ural motorcycles. Allows shifting forward or reverse gears via hand levers alongside gas tank. Design allows normal shifting with foot shift pedal if desired
- $365.00 kit |
 | 2WD Tuff Shaft Ural 2WD side car drive shafts are subject to bending / twisting in rough terrain conditions, jumping the bike (especially under full power) and being overloaded from excessive amounts of gear. Comes now the cure for all but insane conditions - the Tuff Shaft.
- $240.00 each |
 | "Z Bar" Engine Guard Replace your droopy "D" engine guard with our smart and strong "Z Bar" guard. Manufactured from .120” wall electro-welded steel tubing - mandrel formed into a dramatic shape that looks more “correct” than the factory piece. Special CNC machined studs turned from 4130 Chrome Moly stock.
- $125.00 each |
 | Engine Sump Guard 3/16" thick tempered aluminum protects engine oil pan (sump) from damage by obstacles, especially good for off-pavement riding. Black matter powder coating. Drain plug access hole. Mounting hardware included, no drilling required.
- $175.00 each |
 | Foot Box w/Braced Engine Guard Here’s one for the off-road rider! Left side foot rest replaced with comfortable extruded metal floor foot box. Raised lip around perimeter helps prevent rider's foot from slipping off. Braced crash bar will take a considerable “hit” with this system. Foot box is welded to standard foot rest. All bolt on design - no drilling.
- $285.00 each
|
 | Angled Foot Box w/Braced Engine Guard We built this item for Riders equipped with a prosthetic left leg. Works in conjunction with our Twin Stick Shift Kit, or by itself. Permits the prosthetic foot to angle outwards at a comfortable angle. Perimeter lip around foot box aids in preventing the wearer's shoe "going overboard".
- $385.00 each
|
 | Black Rear Sidecar Bumper Black powder-coated 2-rail steel bumper for your sidecar. Protects vulnerable sheet metal below trunk lid. Bumper wraps around corners of tub to protect against angle strikes. Requires drilling two holes to install. Delrin stand-offs and stainless steel installation hardware included.
- $115.00 each |
 | Chrome Rear Sidecar Bumper Chrome-plated twin rail side car bumper protects vulnerable sheet metal below the trunk lid. Wraps around the corners to ward off angle strikes Supplied with Delrin stand-off spacers, stainless steel hardware.
- $115.00 each |
 | Ural Official "Tail Gater" Chrome Rear Sidecar Bumper Urals are all about fun, be the life of any party with this exclusive chrome-plated Tail Gater rear bumper with included bottle opener for your beverage of choice. Requires drilling two holes for installation, Delrin stand-offs and mounting hardware included.
- $145.00 each |
 | Trunk Lock Requires only one hole drilled in trunk sidewall near trunk lid handle. Secures your trunk when you're away from your rig, and the outer half of lock can be stowed when you're not using it. Black powder-coated. Comes with two keys.
- $16.95 each |
 | Helmet Lock Requires only one hole drilled in rear fender valance panel. Secures your helmet when you're away from your rig, and outer half of lock can be stowed when you're not using it. Black powder-coated. Comes with two keys. With some creative thought, can be installed on most any motorcycle.
- $16.95 each |
 | Trunk Lid Mounted Fire Extinguisher Hope you never have to use one, but priceless should the need arise, sometime required by local regulations on forest/service roads, rallies and events, and technically mandatory for travel in Mexico. Type "A" fire extinguisher is held by special brackets to underside of trunk lid. Mounting hardware included, drilled holes required for installation.
- $45.00 each |
 | Side Car Cup Holder We have been asked to supply cup holders for Ural - so here you go! Adaptable to various sizes of drinking cups. Mounts to side car wind- shield grab bar with small hose clamps. Colors available are Black or Gray. Equipped with pen holder.
- $12.95 each (specify Black or Gray color when ordering)
|
 | Side Car Arm Rests Tired of your passenger complaining of bruised elbows and cold steel? Raceway’s answer to the problem are these fiberglass base, padded arm rests. Durable all-weather covering, styling that looks like it belongs there - plus comfort and convince - what more can you ask for?
- $125.00/pair |
 | "Day Long" Saddle Custom-made "Day Long" saddle for your Ural, so called because it's so comfortable, you can ride all day. Black vinyl cover with heavy-duty stitching. Because this saddle is built on a stock Ural seat pan, these saddle are sold on an exchange basis, you send us your old saddle, we send you a "Day Long". If you don't have a saddle pan you want to exchange, Raceway can sell you one at additional cost.
- $478.00 each (seat pan exchange basis) |
 | Sidecar Camo Interior Upholstery Panels Go camo! Cloth-covered upholstery panels with a camouflage pattern to dress up the interior sides of your sidecar's cockpit. Attaches to interior walls with adhesive-backed Velcro tabs, no drilling required.
- $145.00 set
|
 | Diamond Plate Sidecar Nose Underbody Protection Plate Mirror finish diamond plate dresser panel adds not only good great but will also protect the paint finish under the visible and exposed nose of the sidecar. Reflective mirror finish creates a "flash zone" for tail-gating drivers. Mounts to sidecar using same fasteners and holes as front bumper/brush guard). NOTE: Nose plate is shown in photo with Rear Valance Panel (details below) which IS NOT included with the Nose Plate, but must be purchased separately.
- $105.00 each |
 | Diamond Plate Sidecar Rear Valance Panel Mirror finish diamond plate dresser panel adds not only good looks but protection too. Reflective mirror finish creates a "flash zone" for tail-gating drivers. Mounts to sidecar sheet metal with 3M double-sided adhesive body mold tape, no drilling required.
- $24.95 each (Rear Valance Panel Only) |
 | Diamond Plate Sidecar Fender Rock Guard Keep those rock chips at bay! Mirror finish diamond plate anti-rock chip, anti-scuff trim piece adds not only good looks but protection too. Mounts to fender sheet metal with 3M double-sided adhesive body mold tape, no drilling required.
- $34.95 each |
 | Diamond Plate Air Filter Box Dresser Plate Add some style to your air filter box. Mirror finish diamond plate trim piece dresses up your cover and adds some flash at the same time. Easy installation!
- $24.00 each |
 | Diamond Plate Under-Headlight Weather Guard Ural owners like to comment on how they own an "all metal" rig, but then have to admit "ummm - except for this little plastic guard for the electrical wiring under the headlight. Lose that black plastic guard, and replace it with this high-polish, diamond plate guard instead.
- $29.95 each |
 | Diamond Plate Key Shield A big ring of keys can cause ugly scratches and paint scuffing on the left-hand fork cover. Our polished diamond-plate cover will stop the scratching. Install with supplied 3M body side molding double-sided adhesive tape. Compatible with Trim Ring below.
- $24.95 each |
 | Ural Ignition Switch Trim Ring/Bezel The stock ignition lock on an Ural is just sticking out of the headlight shell like a sore thumb. It's really the only "unfinished" assembly on the while bike. Our Trim Ring not only adds a nice finishing touch, but provides additional support to protect the switch. CNC-machined, polished, includes two Allen Head screws to replace the stock slotted round-head screws. Compatible with Key Shield above.
- $13.95 each |
 | Black Sidecar Dashboard with Cut-out (Radio Not Included!) Black vinyl-covered aluminum dashboard for your Ural sidecar. Mounts using same holes and fasteners as your windshield, no drilling required. Dash comes equipped with one rocker switch, 12VDC cigarette-lighter style accessory power outlet and Ural logo. Dash has standard opening for installation of radio or CD player (radio or CD player is not included, unit shown is for illustrative purposes only).
- $115.00 each |
| Blank Carbon Fiber Sidecar Dashboard Carbon fiber dashboard for your Ural sidecar. Mounts using same holes and fasteners as your windshield, no drilling required. Dash comes equipped with two rocker switches, 12VDC cigarette-lighter style accessory power outlet and Ural logo.
- $159.00 each |
| Wood Sidecar Dashboard Carbon fiber dashboard for your Ural sidecar. Mounts using same holes and fasteners as your windshield, no drilling required. Dash comes equipped with two rocker switches, 12VDC cigarette-lighter style accessory power outlet and Ural logo.
- $195.00 each |
 | Sidecar Rear View Mirror Passengers appreciate rearward vision too. Standard chrome or black painter bar-end mirror above has been modified for use as sidecar mirror. Requires drilling one hole for installation, hardware included.
- $29.95 each, available in chrome or black matte painted finish |
 | Chrome "Dresser" Spotlight Bar with Spots (Auxiliary Driving Lights) "Dresser" style light bar will really make you "shine" on the road. Includes two 4" diameter DOT-approved auxiliary driving lights. Pre-wired with 15A toggle switch. Mounts to existing studs under headlight. Auxiliary driving lights are chrome-plated, light bar available in chrome or black powder coat (see below).
- $175.00 each |
 | Black Auxiliary Driving Light Bar Black powder-coated mandrel bent light bar for installing auxiliary driving or fog lamps on your Ural motorcycle. May be used with our lights, or you may purchase your own, lights not included. Mounts directly underneath headlight to existing studs and hardware.
- $79.95 each |
 | Tri-Bar Blue Dot "Hoodie" Halogen 7" Headlight Possibly one of the most interesting motorcycle headlights ever created. Has hooded lens, triangular bars within shell produce stunning visual effect, and blue center jewel sets it all off. Includes replaceable Halogen bulb. Trivial installation, simply remove the one screw that retains the stock headlight, and swap it out. 7" diameter. Not DOT approved, "for off-road use" only.
- $165.00 each |
 | Chrome 7" Diameter Auxiliary Driving Light Can be used with our Light Bar above, or, anywhere else that is stout enough to keep it from vibrating. Looks especially great on a Wolf or Retro model. "Hoodie" lens ring. Halogen bulb included. Requires wiring and switch depending on installation.
- $75.00 each |
 | Sidecar Auxiliary Driving Light 5" or 6" diameter chrome-plated auxiliary driving light equipped with H3 type Halogen bulb. Requires drilling two holes in 15A or greater switch or relay, and wiring. For "off-road or competition" use only.
- $29.95 each |
 | Rear Auxiliary LED Tail Light for Standard Rear Rack Rectangular LED stop/taillight assembly. Mounts with clips to rear rails on standard Ural sidecar rear luggage rack/tire carrier. LIght mounted to aluminum flat bracket, attached with included U-bolts and acorn nuts. Instructions included, do drilling, dome wiring required.
- $69.00 each |
 | Bullet Style Turn Signal or Running Lights Classic chrome-plated bullet style turn signal or running lights for your Ural or any other vehicle. Red lens also available. Flush mount to any flat surface. Requires drilling hole and electrical hook-up and wiring. Rubber anti-chafe gasket included. Not DOT approved, check local regulations before installation.
- $29.95 pair
|
 | Chrome or Black Nose Rack Our newest design rack for the nose of your sidecar. Furnished in gleaming Chrome or Black powder coat at the same price! 3/8” welded steel rod construction - furnished with bungee cord eyelets to tie down light cargo.
- $105.00 each (specify Chrome or Black powder coat when ordering) |
 | Gear-Up Black Nose Rack Black semi-gloss powder-coated MIG-welded nose rack for securing soft luggage. Has provision for clearing the spotlight on Gear-Ups. Stainless steel hardware and mounting point gaskets included. Will accept our slat board kits.
- $125.00 each |
 | Slat Board Kit for Nose Rack White oak, weatherproof Urethane overcoated, stained slat board set for black or chrome nose racks give your rig that vintage look. Slats are grooved underneath, and secured with high-strength sealant and latching brackets. Instructions, hardware and sealant included.
- $99.95 set
|
 | Slat Board Kit for Standard Rear Rack White oak, weatherproof Urethane overcoated, stained slat board set for standard Ural rear rack. Slats are grooved underneath, seated at ends to prevent turning, and secured with high-strength sealant and latching brackets. Instructions, hardware and sealant included.
- $95.00 set |
 | Retro Chrome Trunk Rack Shades of the old MG’s - here’s a retro rack for the Retro! Styling clues are from the “boot” rack found on English sports cars. A nicely-styled addition to an otherwise plain trunk lid.
- $175.00 each |
 | Slat Board Kit for the Retro's Standard Rear Rack Give your already classically vintage Retro a "Woodie" look. White oak, weatherproof Urethane overcoated, stained slat board set for standard Ural rear rack. Slats are grooved underneath, seated at ends to prevent turning, and secured with high-strength sealant and latching brackets. Instructions, hardware and sealant included.
- $85.00 set |
 | Canvas Cargo Belts Canvas cargo belts to secure your soft luggage feature braided eyelets, dual metal latches, steel buckles, and leather hold downs for the belt end. Belts are 1-7/8" wide x 45" long. Two belts included per set.
- $12.95 set (2 each per set) |
 | Genuine Leather Cargo Belts Genuine leather cargo belts to secure your soft luggage feature punched holes, dual metal latches, steel buckles, and leather hold downs for the belt end. Belts are 40" long. Photo shows two belts, but belts are sold individually.
- $16.95 each |
 | Black Powder-Coated Fender Rack Ural factory-designed, stamped steel sidecar fender rack, also used on rear fender in conjunction with solo saddle. Available in semi-gloss black powder coat or chrome. Requires drilling holes in fender, stainless steel installation hardware and anti-chafing gaskets included.
- $115.00 each |
 | Wheel Bearing Conversion Kit Convert those pesky, high drag, difficult to maintain old-style roller wheel bearings to precision sealed ball bearings. Kit includes spacers, washer and bearings needed to convert one wheel. Photo shows three kits, four required if you want to covert your spare wheel.
- $69.95 kit (one kits converts one wheel) |
| |
|
|